Hi, I have an X2 which I have just had to change the CU board out of due to a fault code. The new board has cleared the fault codes but Im now left with a strange error?
The Segway wont start up, instead all I get on the info key is a smiley face but with a slit eye and the red warning triangle with the exclamation mark. The Segway goes through its light sequence then flashes 6 times (all lights red) and goes off. Any help really appreciated please
Many thanks
Ramsey.
Segway Fault/Help please
Technik-und Reparatur-Tipps
-
- Beiträge: 2
- Registriert: 13.08.2018 18:32
- mathiegi
- gold-member
- Beiträge: 2418
- Registriert: 07.03.2010 23:37
- Wohnort: Baar (ZG) Schweiz
- Kontaktdaten:
Re: Segway Fault/Help please
hi Ramsey
it the new CU Board programmed to the right S/N?
it the new CU Board programmed to the right S/N?
Liebe Grüsse
mathiegi/der Segwayflüsterer
DIE SEGWAY SCHRAUBER
https://www.facebook.com/groups/DieSegwaySchrauber/
www.youtube.com/user/mathiegi/
Segway? Ich steh drauf!
mathiegi/der Segwayflüsterer
DIE SEGWAY SCHRAUBER
https://www.facebook.com/groups/DieSegwaySchrauber/
www.youtube.com/user/mathiegi/
Segway? Ich steh drauf!
-
- Beiträge: 2
- Registriert: 13.08.2018 18:32
Re: Segway Fault/Help please
Beitrag von Ramsey0007 »
Im not sure to be honest. I had two faults. The first was that I had a failed CU board so swapped it and the segway ran for about 30 minutes. I put the Segway back together and it then stopped working with a E04A error . Looking at the error it looked like it might be a BSA issue so swapped that and then got the above error so you might be right re serial numbers. I have now gone back to the original setup and have an E04A error? Any ideas please?
For my knowledge as I have 10 segways, do the CU boards have to be registered to each other and the BSA in someway therefore not swappable? The reason I ask is I have a dead Segway I use for spares?
Thanks for your help
Rams
For my knowledge as I have 10 segways, do the CU boards have to be registered to each other and the BSA in someway therefore not swappable? The reason I ask is I have a dead Segway I use for spares?
Thanks for your help
Rams
- spiagei
- Beiträge: 306
- Registriert: 30.10.2013 00:28
- Wohnort: Waging
- Kontaktdaten:
Re: Segway Fault/Help please
Hello Rams,
the A-Board (Rear) have to be programmed from Segway. The B-Board not.
E04A Informe CU B CU - BSA DOWN:
First clean the Contacts with Contact 60 Plus. Try again.
If not, i Just had the Error E042. It´s the same Error, but Board A (Rear).
Check and measure the purble cables from CU to the BSA. If there is more than 0,5 Ohm, then you have to soldering them on the Platine. This solved the Problem last time.
Stefan
the A-Board (Rear) have to be programmed from Segway. The B-Board not.
E04A Informe CU B CU - BSA DOWN:
First clean the Contacts with Contact 60 Plus. Try again.
If not, i Just had the Error E042. It´s the same Error, but Board A (Rear).
Check and measure the purble cables from CU to the BSA. If there is more than 0,5 Ohm, then you have to soldering them on the Platine. This solved the Problem last time.
Stefan
https://www.baufi-chiemgau.de/startseite/reparatur-von-segway-pts/
Der Segway Service Partner im Chiemgau und im Voralpenland
Nutzen Sie auch unseren mobilen Werkstattservice
Der Segway Service Partner im Chiemgau und im Voralpenland
Nutzen Sie auch unseren mobilen Werkstattservice
Gehe zu
- Neu hier im Forum ?
- Allgemeines
- Segway GEN2 (ab 2006) und GEN2 SE (ab 2014)
- Segway GEN1 (bis 2006) RMPs, iBOT®
- Zubehör / Modifikationen / An- und Umbauten
- Technik
- Veranstaltungen
- Bilder & Videos
- Touren & Verleihmöglichkeiten
- Presse
- An- und Verkauf
- Rechtliches
- Segway-Polo und andere Segway-Sportarten
- Barrierefreiheit
- Board-Infos
- ↳ Tipps über dieses Forum / News
- Segway-Chat
- ↳ Segway General Discussions
- ↳ Events
- über unseren Sponsor
- Ninebot / andere Elektrofahrzeuge